Saturday 30 July 2016

Continuing work on the Mounted Arabs and AWI.

Work is progressing on the Arab Warriors, I have four mounted units in progress at the moment. Two units of six heavy cavalry with spears, one unit of light cavalry archers and finally, one unit of light cavalry javelins.


First unit of six figures which are heavy cavalry with spears.



Second unit of heavy cavalry with spears.



Light cavalry with javelins in front, with light cavalry with bows behind.



With the completion of the scratch built fort for the French & Indian Wars/War of Independence, I couldn't resist taking a sprue from the Liberty or Death box set to paint up a few test figures.


As you can see from this artwork of the troops contained in the box, The figures top left, top right and bottom right, are going to be very tricky to paint the waistcoat and jacket trims with the arms and weapons in place.


So for the six test figures I have begun with torsos. I am using a completely new technique for me, namely I primed the plastic, I normally coat them in PVA. I have also painted the bases with textured paint, again a first for me, regular followers of this blog will know I am old school and just use flock. The paint is being done in layers, all the paints are Vallejo.



Jackets Flat Red, Waistcoat, trousers, belts and turn backs in Stonewall Grey. Next a wash with Umber wash.


I used exactly the same base colours again to highlight, concentrating on the folds etc. Again this is totally alien to me, but I was determined to experiment.


I then highlighted again, this time the Jacket with Vermillion and the white areas with Wolf Grey. A final highlight, using Off White for the belts and White for the waistcoat and trousers.

A totally new way to paint for me, but so far, I am quite pleased with the results and the arms can now be attached. Hopefully causing little or no damage to the paintwork.

Tuesday 26 July 2016

Fort now finished and ready for the table.

So this brings to an end my little scratch built fort. It has cost me under £2 to build and as well as being unique, it was fun to build. It will now be ready for when I paint up the figures to garrison it.
Many thanks for all the positive comments I have received on this mini series of blog posts. I hope you enjoyed it as much as I did.


Using the tray again to give me a level both vertically and horizontally. The blue tack is used to keep the logs packed tight as the glue dries.


Exactly the same treatment for the other gate, this is made of five posts as opposed to the six of the other gate. It had to be that way to fit the opening.



I also put textured paint down inside the fort, to simulate the packed earth.


Those plank walkways will be well used during the muddy season!



I also took the opportunity to stain the floor of the cabins, the roofs are all removable to allow for the placing of troops inside, if the rules allow for it.



The final act was to try the gate, dry fitted here.



Again a dry fit and partly opened.



I made some hooks and eyes out of 30 amp fuse wire to attach the gates.



Attached in position, that was a giggle fitting them, NOT!



But the plan worked and the gates in the open position.





Closed to keep the enemy at bay.



I am going to call that complete! It still needs a flag pole to finish it off at some point in the future.

Monday 25 July 2016

The fort nears completion.

I have added the two final buildings to the fort, also plank walkways outside the doors. I imagine the centre, though packed down earth, could get a little muddy at times. It would be great to grass that area, but of course soldiers drilling and marching would soon get rid of any vegetation. So it will have to be textured in some way. I am now pondering on how to fit the gates, I am thinking along the lines of a paper clip ring and two hooks on each gate post to allow them to be opened and closed.


Cutting the hut out of balsa and a dry fit.


The same with the other hut.


The sides of the building help to support the walkway above.


The cans of soup and tomatoes come in handy again in the PVA drying process.


Two cans for the larger hut.


First one almost complete, the stove pipe needs a coat of black.


Hut number two also virtually finished.


Still plenty of room in the centre for parading the troops.


Some shots taken outside, you can also see the two new plank walkways outside the new huts, they now link in with the original.




A top down shot, shows plenty of area in the centre.

Sunday 24 July 2016

Further progress on the fort.

Well, I have spent a lot of time on the fort today, or yesterday as it is now at 2:45 am, damn heartburn! So whilst I am sat here waiting for it to pass, I may as well occupy my mind and show what I have accomplished  so far.


The whole structure is now complete, the logs placed above the gateway being the final addition.


I then went round each individual palisade log and made sure PVA glue was in the cracks between each of them. This will give the structure even more rigidity.



At this point all the glue is drying outside in the warmth.



A pretty small fort, but at a foot square, it will be more than big enough for my table.



I gave the palisade walls two coats of Mocha acrylic paint and then dry fitted some balsa pieces to make a building with two rooms. Commanders quarters and officers mess perhaps.



Painted the doors blue and the walls grey. Also scored the walls to look like boards/planks.



A roof from very thin balsa upon which, I scored the tiles and added a couple of stove pipes. The roof is removable, but is quite fragile, so I may end up having to make a one from thicker material.



Peering in through the gateway, you can just make out the boarding on the building.

I may add another building along one side, not sure yet. I also want to place some planking or similar outside the building(s). The rest of the base will need to be textured to resemble packed earth, plus of course I need to build and fix a pair of gates. So far, this project has cost me less than £2, I had to buy another two packs of garden plant sticks, which I cut down for the palisade.

The fort continues to take shape.

I have done some more work on the fort today, cutting 100 mm lengths of garden stakes and then sharpening one end. I then again used my tray to keep everything square and built the other walls. It is of course only held together with PVA (white wood glue) so it is going to need extra strengthening pieces added, but the outer walls are now attached to the base, with a gap for the gate.


The second wall section constructed on the tray.


Third wall constructed, glued and drying, I didn't realise we had so much soup in the cupboard!



Rear and two side walls complete.



First of the two front wall sections.


The second section of the front wall, a bit more tricky as I have left a gap for the gate.



All the pieces now glue together and drying. I also added the walkways to give more gluing area to hold it all together. I will be putting polyfilla (spackle) all around the base, inside and out, to anchor the bases of the walls.



The walkway is about 25 mm wide so should take a soldier on its base without a problem.



So far, so good. I am quite pleased with how it is looking so far. A lot of work still to be done of course, but it should make a nice piece of scenery for the war gaming table eventually.

So that is the position at the end of the afternoon, I am thoroughly enjoying myself building this and I hope to be able to add the polyfilla/spackle at the base of the four walls this evening to allow it to dry thoroughly overnight. I am hoping to put a building or two inside, probably attached to the palisade fences as this will also help the strengthen the structure.